中华人民共和国水产行业标准sc/T8018一94渔船吊杆代替SC18-79，主题内容本标准规定了渔船吊杆的型式、基本尺寸、技术要求、试验方法和检验规则。2引用标准GB5117ZBH21碳钢焊条002柴油机动力海洋渔船系泊航行捕捞试验通则3渔船吊杆型式和墓本尺寸3.1渔船吊杆型式见图10图11吊杆叉头;2一羊角;3吊杆锥体段;4一吊杆中段;5一吊环;6一稳索眼板;7一吊货眼板;8一吊杆眼板处复板;9一封头板;1。一垫板3.2渔船吊杆基本尺寸见表to中华人民共和国农业部1994一10一0，批准1995一01一01实施sC/T8018一94表1吊杆轴向压力，kNI1DD,tL1,1,G截面惯性矩质量,kg们1mn】0h4Jocm"D,l}tJ,cm0叉头为焊接叉头为铸钢30.04.905.001331336400500300200518518180.005.906.001461466400500300200648648191.88右.907.001521526400500300200735735219.9850.07.507.601591367400500300250967556267.75267.248.008.1018015474005003002501426740301.67301.141009.8010.00219165840070040025029561219499.89498.781308.839.00219165840070040025029561219475.12475.071507.838.00219175840070040025029561467436.06436.018.839.00230184840070040025029561467501.97501.929.8310.00245190840070040025041881897580.62580.221808.839.00245190840070040025041881897536.94536.542008.829.00273205840070040025058532406596.03595.2313吊杆稳索眼板的型式和基本尺寸见图z及表zo，一按理场实际尺寸定A视许用负荷kN吊杆末端直径D,万召BRrS质量kgmm15一30133-15460601504520282.5330一4016565641645025一:82.6260175-19070641765628353.878020575641846030406.323.4吊杆吊货眼板的型式和基本尺寸按图3及表3}sc/T8018一94许用负荷kN吊杆末端直径D,Aa】BRR,rs质量kgmm15^30133-1542602013547.53017.53410.0030-401653003016060.54022.53815.6060175-1903404022870.04527.54217.80802053565023580.05532.54628.503-5吊杆叉头型式和主要尺寸见图4、图5及表4)图4焊接叉头图5铸钢又头D,--0.6D.SC/T8018一94表4吊杆轴向压力，kN吊杆末端内壁直径B6oDoD口2d月人h,天sto乙1C质量，kg们1们匕焊接铸钢30121803211813031784430161236125.306.201311441346.5113715014050122903711913436884835201236128.510.9513715214011.6811.1310014910047146165一‘一卜1叮，:.51125S11芍50{6113671206e3016421414.6214.125713015.81S.315517515015912016.2115.7116418416817.016.617019017417.016.61701901B017468185...
