第一篇：船舶制造英语日常用语- 船体

船舶制造英语日常用语-船体

1．You must weld and grind this area before painting.在油漆之前你必须把这个地方电焊修补、打磨好。2．

This welding line should be gouged and welded again before tightness inspection.这条焊缝在密性检查前要碳刨、再焊。

3．The structure of the starboard side is different from the port side.右舷的结构跟左舷的不一样。

4．We should reinforce the downside of the windlass.我们应该在锚机的反面加强。

5．The navigation deck is not plain, we will fair the deck by hot working.驾驶甲板不平，我们要火工校正。

6．There are two pieces of stiffeners and brackets must be replaced.有两块加强筋和肘板要换新。7．

Two more footrests and handgrips should be installed at the entrance of the small hatchcover.在小舱口盖的进口处再安装两只踏步和拉手。

8．Checking the joint accuracy and structure integrity between No.8 and No.9 block after closed.No.8 与No9分段合拢后大接头装配精确性和结构完整性检查。

9．Checking structure integrity of superstructure(deckhouse)after welding.上层建筑焊后结构完整性检查。

10．Inspecting fitting accuracy of hatch coaming on board.货舱口围板船上安装精度检查。

11．Inspection air pressure test(with water head)for No1.water ballast tank(No15 block).No1压载水舱（No.15分段）气压试验（压头试验）检查。12．

Inspection hosing test for upper deck.上甲板冲水试验检查。

13．Measuring hull’s main dimensions: length overall(LOA.),length between perpendiculars(LPP.),breath molded(B.),depth molded(D.)and deflection before launching.下水前测量船体主尺度：总长、两柱间长、型宽、型深、基线挠度。

14．Inspection distance between draught marks and keel plate after marking out.划线后检查吃水标尺至平板龙骨之间的距离。

15．Inspecting fitting accuracy of draught mark(loading line mark).吃水标志（载重线标志）安装精确性检查。

16．Inspection welding seam and dimension of cargo hatch cover.货舱舱口盖焊缝和尺度检查。

第二篇：船舶制造英语日常用语

船舶制造英语日常用语 一． 船体

1． You must weld and grind this area before painting.在油漆之前你必须把这个地方电焊修补、打磨好。

2． This welding line should be gouged and welded again before tightness inspection.这条焊缝在密性检查前要碳刨、再焊。

3． The structure of the starboard side is different from the port side.右舷的结构跟左舷的不一样。

4． We should reinforce the downside of the windlass.我们应该在锚机的反面加强。

5． The navigation deck is not plain, we will fair the deck by hot working.驾驶甲板不平，我们要火工校正。6． There are two pieces of stiffeners and brackets must be replaced.有两块加强筋和肘板要换新。

7． Two more footrests and handgrips should be installed at the entrance of the small hatchcover.在小舱口盖的进口处再安装两只踏步和拉手。

8． Checking the joint accuracy and structure integrity between No.8 and No.9 block after closed.No.8 与No9分段合拢后大接头装配精确性和结构完整性检查。

9.Checking structure integrity of superstructure(deckhouse)after welding.上层建筑焊后结构完整性检查。

10． Inspecting fitting accuracy of hatch coaming on board.货舱口围板船上安装精度检查。

11． Inspection air pressure test(with water head)for No1.water ballast tank(No15 block).No1压载水舱（No.15分段）气压试验（压头试验）检查。12． Inspection hosing test for upper deck.上甲板冲水试验检查。

13． Measuring hull’s main dimensions: length overall(LOA.),length between perpendiculars(LPP.),breath molded(B.),depth molded(D.)and deflection before launching.下水前测量船体主尺度：总长、两柱间长、型宽、型深、基线挠度。14． Inspection distance between draught marks and keel plate after marking out.划线后检查吃水标尺至平板龙骨之间的距离。

15． Inspecting fitting accuracy of draught mark(loading line mark).吃水标志（载重线标志）安装精确性检查。

16． Inspection welding seam and dimension of cargo hatch cover.货舱舱口盖焊缝和尺度检查。

二． 轮机

1．Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).螺旋桨轴（中间轴）机加工尺寸检查。2． Check for surface contact area(metallic contact)between stern shaft and propeller hub tapers.检查螺旋桨轴与螺旋桨锥度接触面。3． Inspection machining dimension of rudder stock.舵杆机加工尺寸检查。

4． Inspection rudder carrier after assembly.上舵承组装后检查。

5． Inspection machining dimension of rudder pintle.舵销机加工尺寸检查。

6． Inspection alignment of stock, rudder blade and pintle.舵杆、舵叶、舵销连接后中心线检查。

7． Lowering test and tension test of anchor.锚投掷试验和拉力试验。

8． Measuring dimension of shaft coupling bolts and reamer hole.轴系连接螺栓和钻孔尺寸测量。

9．Inspection installation correctness of ship’s name plate(funnel mark).船名牌（烟囱标志）安装正确性检查。

10． Flexibility and hosing test for small water tight hatch cover(water tight door and window).水密小舱口盖（水密门、窗）启闭灵活性、冲水检查。11． Tightness test(opening and closing test,emergency opening and closing test)for cargo hatch cover.货舱舱口盖密性试验（启闭试验、应急启闭试验）。

12． Inspecting anchor throwing away appliance.弃锚装置检查。

13． Inspecting centerline positioning for shaft system and rudder system before boring.轴、舵系镗孔前中心线定位检查。

14． Optical aligned check for shaft system after boring.轴系镗孔后光学校中检查。

15． Hydraulic test for L.O.pipe for stern tube.艉轴管滑油液压试验。

16． Measuring diameter of fore and aft stern tube bearing and bushes.艉轴管前、后轴承与衬套直径测量。

17． Inspection push-up load for fore and aft stern tube bushes.艉轴管前、后衬套压入检查。18． Measuring clearance between propeller shaft & bearing.螺旋桨轴与轴承间隙测量。

19． Flushing L.O.system of stern tube.艉轴管滑油系统的投油清洗。

20． Inspecting zero(datum)position of rudder blade.舵叶0位检查。

21． Measuring clearance of rudder jumping stopper.舵止跳块的间隙测量。

22． Inspecting integrity of steering gear.操舵装置完整性检查。

23． Measuring installation clearance of rudder bearing.舵轴承安装间隙测量。

24． Flushing of piping system for steering gear.舵机管路系统的投油清洗。

25． Mooring test of steering gear.舵机系泊试验。

26． Manoeuving test of steering gear during sea trial.舵机航行中操舵试验。

27． Emergency manoeuving test of steering gear.舵机应急操舵试验。

28． Installation and alignment inspection of windlass.锚机安装与校中检查。

29． Anchoring and weighing test of windlass on sea trial.锚机航行中抛起锚试验。

30． Adjusting safety device for hydraulic system of steering gear(windlass、mooring winch).舵机（锚机、绞缆机）液压系统安全装置调整。

31． Running test and loading test for 4t provision crane.4吨食物吊运转试验和吊重试验。

32． Lowering and hoisting test for life boat.救生艇收放试验。

33． Loading test of accommodation ladder(pilot ladder).舷梯（引水员梯）压重试验。

34． Checking liner of main engine(M.E.).主机垫片检查。

35． Tightening inspection for through bolts of main engine(M.E.).主机贯穿螺栓紧固度检查。

36． Aligning main engine’s crank shaft and intermediate shaft after launching.下水后主机曲轴和中间轴连接后校中。

37． Aligning intermediate shaft and propeller shaft after launching.下水后中间轴和螺旋桨连接后校中。

38． Measuring deflection of crank shaft of M.E.before starting up(after sea trial).主机动车前（航行试验后）曲轴甩档测量。

39． Flushing lubrication oil(fuel oil)system of M/E.主机滑油（燃油）管路投油清洗。40． Alignment inspection installation of shaft generator and gear box.轴带发电机及齿轮箱安装检查。

41． Alarm testing and safety device testing of M/E.主机报警和安全装置试验。42． Mooring test(sea trial)of M.E.and inspection attached pumps and piping system.主机系泊（航行）试验并检查其附属泵与管路。

43． Running test of shaft generator and clutching test between M.E.and shaft generator.轴带发电机运转试验及主机与轴带发电机之间的离合器的效用试验。44． Change over test between shaft generator and diesel generator on sea trial.航行试验中轴带发电机与柴油发电机之间的换车试验。45． Overhauling main engine after sea trial.主机航行试验后的拆检。

46． Installation inspection of main diesel generator.主柴油发电机组安装检查。

47． Safety device testing for emergency diesel generator.应急柴油发电机的安全装置试验。48． Charging test and safety valve and automatic device adjusting for main compressor(auxiliary compressor).主（辅）空气压缩机的充气试验、安全阀和自动装置的调整。

49． Air tightness test and safety valve adjusting for main air receiver(control air receiver, air horn receiver)on board.主空气瓶（控制空气瓶、汽笛空气瓶）装船后气密试验和安全阀的调整。

50． Safety valve adjusting and accumulating test for auxiliary boiler.辅锅炉安全阀检验及蓄压试验。

51． Air tightness test for auxiliary boiler(economize boiler)on board.辅锅炉（废气锅炉）装船后气密试验。

52． Automatic controller test for auxiliary boiler.辅锅炉自动控制装置试验。

53． Function test for economizer.废气锅炉效用试验。54． Function test and automatic controller test for ballast pump.压载泵效用试验和自动控制装置试验。55． Function test of bilge oily water separator(sewage treatment plant, fresh water generator, incinerator).舱底水油水分离器（污水处理装置、制淡装置、焚烧炉）效用试验。

三． 电气

1． Inspection main cable installation for wheel house before paneling decoration.敷板前驾驶室检查主干电缆安装.2．

Measuring insulation resistance and reliability test protection device for main switchboard(emergency switchboard).总配电板（应急配电板）绝缘电阻测量和保护装置可靠性试验。

3． Load and performance test for main generator(emergency generator).主发电机（应急发电机）负荷及特性试验。

4． Automatic governing test of voltage and frequency for main generator(emergency generator).主发电机（应急发电机）电压、频率自动调节试验。

5． Parallel-running test for main generator.主发电机并联运行试验。

6． Diesel generator voltage characteristic test.柴油发电机电压特性试验。

7． Diesel generator governor sensitivity test.柴油发电机调速特性试验。

8． Test for taking on a full load suddenly.突加负荷试验。

9． Reverse power relay trip test.逆功率脱扣试验。

10． Over-current relay test.过电流脱扣试验。

11． Under voltage tripping test.低压脱扣试验。

12． Interlocking reliability test.联锁试验。

13． Load test for shaft generator and its function test on sea trial.轴带发电机负荷试验和航行时效用试验。

14． Automatic supply test of emergency generator.应急发电机自动供电试验。

15． Calibrating rudder angle indicator.舵角指示器校准。

16． Remote starting and alarm test for steering gear motor.舵机马达遥控起动和报警试验。

17． Function test automatic pilot.自动舵效用试验。

18． Sequence starting and automatic exchange of motors for auxiliary machine and pump.辅机和泵的电动机程序起动和自动转换。

19． Charge and discharge operation test for battery and charge equipment.蓄电池和充电装置的充放电试验。20． Operation test of emergency switching-off device for oil pump and ventilator(bilge pump)in engine room.机舱风、油（舱底泵）应急切断装置操作试验。

21． Remote control test for fire pump and emergency fire pump.消防泵、应急消防泵遥控操作试验。

22． Function test of fog horn.雾笛效用试验。

23． Inspection installation and water tightness transducer of echo sounder on berth.测深仪换能器船台安装和水密性检查。

24． Function test and adjust error for log on sea trial.航行试验中计程仪效用试验及误差调整。

25． Function test and calibration self-heterodyne curve for direction finder on sea trial.航行试验中测向仪效用试验及自差曲线校正。

26． Inspection installation for antenna of radio console and measuring its insulation resistance.组装报务台天线安装检查和绝缘测量。

27． Function test of radio console on sea trial.航行试验中组装报务台效用试验。

28． Calibration constant error and function for gyro-compass on sea trial.航行试验中电罗经固定误差校正和效用试验。

29． Function test of radar on sea trial(mooring test).航行试验（系泊试验）中雷达效用试验。

30． Simulating(Automatic)alarm test for fire detector.火警检测器模拟（自动）报警试验。

31． The items are tested according to mooring test program as following : 下列项目按系泊试验大纲进行系泊试验：

32． Function test of engineer calling device(call device in hospital).轮机员呼叫（病室呼叫）装置试验。

33． Function test of ultra-short wave radio telephone.超短波对讲机。

34． Function test of remote control system of main engine.主机遥控系统性能试验。35． UMS(unattended machinery space)sea trial continue 4~6 hours.无人机舱作4~6小时航行试验。36． Measuring insulation resistance for circuit.电路绝缘电阻测量。

37． Function test for weather facsimile receive.气象传真机效用试验。

四． 上层建筑

1． A/C duct and vent duct structure of W/H Deck.驾驶甲板空调、机械风管结构。

2． Inspection the structure and loading test of the lifeboat(Rescue boat)davit.救生（助）艇吊架结构和压重试验。3． Ref.Freon piping to be done air-tightness test and vacuum test.冷藏氟利昂管系密性试验和真空试验。

4． Ref.Plant to be done protection device test and cooling-down test.冷藏机组保护装置试验及打冷试验。

5．Accommodation air-condition Freon piping to be done air-tightness and vacuum test.房舱空调氟利昂管系密性试验和真空试验。

6． Accommodation to be done air flowing adjustment test.房舱风量调整试验。

7． E/C room Package A-C to be done function test.集控室单位式空调效用试验。

8． E/R air drier to be done function test and alarm test.机舱空气干燥器效用试验及报警试验。

9． Superstructure water-tightness doors and windows to be done hosing test.上层建筑水密门窗冲水试验。

10． Cabin supply fan to be done function test.房舱风机效用试验。

11． Superstructure lifesaving and fire fighting equipment to be done inspection.上层建筑救生、消防设备交验。

12． Galley and laundry equipment to be done function.厨房、洗衣间设备交验。

13． Refrigerator to be done function test.冰箱效用试验。14． Rescue boat davit(life raft davit)to be done static(dynamic)loading test.救助艇架（救生筏吊架）静（动）负荷试验。

15． Mushroom outlet closing and opening by hand to be inspected.菌形风帽手动启闭试验。

16． Superstructure compressed air(water supply、fire fighting、smoke detection)piping to be done air-tightness test.上层建筑压缩空气管系（供水管、消防管、烟雾探测管）密性试验。

17． Cabin condensation piping to be done free-flowing test.房舱凝水、落水管系畅通试验。

18． Deck flushing piping system to be done air-tightness test.甲板冲洗管系密性试验。19． Painting RM.Fire fighting pipe to be done air-tightness test.油漆间消防管系密性试验。

20． W/H water spray pipe to be done function test.驾驶室水喷淋管系效用试验。

21． Insulation of A-deck(including A60 insulation).A甲板绝缘（包括A甲板A60绝缘）。

22． Floating floor of E/C RM.集控室浮动地板。

23． Insulation of emergency generator room(including A60 insulation).应急发电机室绝缘（包括应急发电机室A60绝缘）。

24． Insulation of escape in E/R.(including A60 insulation).机舱逃口绝缘（包括机舱逃口A60绝缘）。25． Insulation of F11# bulkhead in E/R.(including A60 insulation).F11#舱壁绝缘（包括F11#舱壁A60绝缘）。

26． Completeness of all cabins to be inspection.全船房舱完整性提交。

27． Inspection insulation installation for master room, Chief engineer room，electrical engineer room before install panel.船长室、轮机长室、电机员室上板前检查隔热安装。

28． Completeness delivery of accommodation(joiner work and interior decoration of accommodation)for master room(chief engineer room).船长室（轮机长室）舱室完整性（木工和内部装饰）提交。

船检业务用英语

1、船体

1.56分段完工后结构完整性和焊缝检查 Inspection structure integrity and welding seam on completing No.56 block.2.上层建筑完后结构完整性检查

Inspection structure integrity after completing the superstructure.3.No.8 与No9分段合拢后大接头装配精确性和结构完整性检查

Checking the joint accuracy and structure integrity between No.8 and No.9 block after closed.4.上层建筑合拢后结构完整性检查

Checking structure integrity of superstructure(deckhouse)after closed.5.货舱口围板船上安装精度检查 Inspecting fitting accuracy of hatch coaming on berth.6.货舱口围板焊接后焊缝检查

Inspecting welding seam of hatch coaming after welding.7.No1压载水舱（No.15分段）气压试验（压头试验）检查

Inspection air pressure test(with water head)for No1.ballast water tank(No15 block).8.上甲板冲水试验检查

Inspection hosing test for upper deck.9.下水前测量船体主尺度、总长、两柱间长、型宽、型深、基线挠度 Measuring hull’s main dimensions:length overall(LOA.),length between perpendiculars(LPP.),breath molded(B.mld.),depth molded and deflection before launching.10.划线后检查吃水标尺至平板龙骨之间的距离

Inspection distance between draught marks and keel plate after marking out.11.吃水标志（载重线标志）安装后精确性检查

Inspecting fitting accuracy of draught mark(loadline mark).12.载重线标志划线后检查尺度

Inspection dimension of loadline after marking out.13.舵叶完工后检查

Checking rudder after completing(finished).14.货舱舱口盖焊缝和尺度检查

Inspection welding seam and dimension of cargo hatch cover.2、轮机内场

1.螺旋桨轴（中间轴）机加工尺寸检查

Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).2.检查螺旋桨轴与螺旋桨锥度接触面

Check for surface contact area(metallic contact)between stern shaft and propeller hub tapers.3.舵杆机加工尺寸检查

Inspection machining dimension of rudder stock.4.上舵承组装后检查

Inspection rudder carrier after assembly.5.舵销机加工尺寸检查

Inspection machining dimension of rudder pintle.6.舵杆、舵叶、舵销连接后中心线检查

Inspecting alignment of stock, rudder blade and pintle.7.锚投掷试验和拉力试验

Lowering test and tension test of anchor.8.轴系连接螺栓和孔尺寸测量

Measuring dimension of coupling bolts and reamer hole.3、轮机外场安装（钳工）

1.防蚀板布置正确性检查

Inspection arrangement correctness of aluminium Anodes.2.船名牌（烟囱标志）安装正确性检查

Inspection installation correctness of ship’s name plate(funnel mark).3.水密小舱口盖（水密门、窗）启闭灵活性检查

Flexibility and hosing test for small water tight hatch cover(water tight door and window).4.货舱舱口盖密性试验（启闭试验、应急启闭试验）

Tightness test(opening and closing test,emergency opening and closing test)for cargo hatch cover.5.弃锚装置检查

Inspecting anchor throwing away appliance.6.轴、舵系镗孔前中心线定位检查

Inspecting centerline positioning for shaft system and rudder system before boring.7.轴系镗孔后光学校中检查

Optical aligned check for shaft system after boring.8.艉轴管滑油液压试验

Hydraulic test for L.O.pipe for stern tube.9.艉轴管前、后轴承与衬套直径测量

Measuring diameter of fore and aft stern tube bearing and bushes.10.艉轴管前、后衬套压入检查

Inspection push-up load for fore and aft stern tube bushes.11.螺旋桨轴与轴承间隙测量

Measuring clearance between propeller shaft & bearing.12.螺旋桨压入检查

Inspection wet fitting the propeller.13.艉轴密性装置的安装与密性试验

Fitting and tightness testing of propeller shaft before launching(after sea trial).14.艉轴管滑油系统的投油清洗 Flushing L.O.system of stern tube.15.舵叶0位检查

Inspecting zero(datum)position of rudder blade.16.舵装置完整性与轻便性检查

Inspecting integrity and flexibility of rudder appliance.17.舵止跳块的间隙测量

Measuring clearance of rudder jumping stopper.18.操舵装置完整性检查

Inspecting integrity of steering gear.19.舵轴承安装间隙测量 Measuring installation clearance of rudder bearing.20.舵机管路系统的投油清洗

Flushing of piping system for steering gear.21.舵机系泊试验

Mooring test of steering gear.22.舵机航行中操舵试验

Manoeuving test of steering gear during sea trial.23.舵机应急操舵试验

Emergency manoeuving test of steering gear.24.锚机管路系统的投油清洗

Flushing of piping system for windlass.25.锚机安装与校中检查

Installation and alignment inspection of windlass.26.锚机系泊试验 Mooring test of windlass.27.锚机航行中抛起锚试验

Anchoring and weighting test of windlass on sea trial.28.绞缆机完整性检查

Inspection integrity of mooring winch.29.绞缆机管路系统的投油清洗

Flushing of piping system for mooring winch.30.绞缆机系泊试验

Mooring test of mooring winch.31.舵机（锚机、绞缆机）液压系统安全装置调整

Adjusting safety device for hydraulic system of steering gear(windlass、mooring winch).32.4吨食物吊运转试验和吊重试验

Running test and hoisting test for 4t provision crane.33.救生艇收放试验

Lowering and hoisting test for life boat.34.救生艇航行试验 Sea trial for life boat.35.舷梯（引水员梯）压重试验

Loading test of accommodation ladder(pilot ladder).36.舷梯（引水员梯）和绞车收放试验

Lowering and hoisting test of accommodation ladder(pilot ladder).37.货舱舱口盖启闭试验

Opening and closing test for cargo hatch cover.38.货舱舱口盖应急启闭试验

Emergency opening and closing test for cargo hatch cover.39.水密小舱口盖（水密门、窗）启闭灵活性检查和冲水试验

Flexibility and hosing test for small water tight hatch cover(water tight door and window).40.主机垫片检查 Checking liner of main engine(M.E.).41.主机贯穿螺栓紧固度检查

Tightening inspection for through bolts of main engine(M.E.).42.下水后主机曲轴和中间轴连接后校中 Aligning main engine’s crank shaft and intermediate shaft after launching.43.下水后中间轴和螺旋桨连接后校中

Aligning intermediate shaft and propeller shaft after launching.44.主机动车前（航行试验后）曲轴甩档测量

Measuring deflection of crank shaft of M.E.before starting up(after sea trial).45.主机滑油（燃油）管路投油清洗

Flushing lubrication oil(fuel oil)system of M/E.46.轴带发电机及齿轮箱安装检查

Alignment inspection installation of shaft generator and gear box.47.主机报警和安全装置试验

Alarm testing and safety device testing of M/E.48.主机系泊（航行）试验并检查其附属泵与管路

Mooring test(sea trial)of M.E.and inspection attached pumps and piping system.49.轴带发电机运转试验及主机与轴带发电机之间的离合器的效用试验 Running test of shaft generator and clutching test between M.E.and shaft generator.50.航行试验中轴带发电机与柴油发电机之间的换车试验 Change over test between shaft generator and diesel generator on sea trial.51.主机航行试验后的拆检

Overhauling main engine after sea trial.52.主柴油发电机组安装检查

Installation inspection of main diesel generator.53.主柴油发电机动车前（系泊试验后）曲轴甩档测量

Measuring deflection of crank shaft of main diesel generator before running test(after sea trial).54.主柴油发电机的报警和安全装置试验

Alarm and safety device testing of main diesel generator.55.主柴油发电机运转试验

Running test of main diesel generator.56.应急柴油发电机运转试验

Running test of emergency main diesel generator.57.应急柴油发电机的安全装置试验

Safety device testing for emergency diesel generator.58.主（辅）空气压缩机的充气试验、安全阀和自动装置的调整

Charging test and safety valve and automatic device adjusting for main compressor(auxiliary compressor).59.应急空气压缩机的运转试验、安全阀和安全装置的调整

Running test and safety valve and safety device adjusting for emergency compressor.60.主空气瓶（控制空气瓶、汽笛空气瓶）装船后气密试验和安全阀的调整

Air tightness test and safety valve adjusting for main air receiver(control air receiver, air horn receiver)on board.61.辅锅炉（废气锅炉）装船后气密试验

Air tightness test for auxiliary boiler(economize boiler)on board.62.辅锅炉安全阀检验及蓄压试验

Safety valve adjusting and accumulating test for auxiliary boiler.63.辅锅炉自动控制装置试验

Automatic controller test for auxiliary boiler.64.废气锅炉效用试验 Function test for economizer.65.压载泵效用试验和自动控制装置试验

Function test and automatic controller test for ballast pump.66.舱底水油水分离器（污水处理装置、制淡装置、焚烧炉）效用试验 Function test of bilge oily water separator(sewage treatment plant, fresh water generator, incinerator).67.机舱行车吊重试验

Hoisting test of engine room crane.68.机修间设备运转试验

Running test of machines in repair room.无线电话 radio telephone 电视机和收音机 TV and radio set 电视机和收音机天线共用器 antenna multi coupler of TV and radio set 电罗经 gyro comp 罗经 magnetic compass 电脉冲 electrical impulse 应急电站 emergency power station 扬声器 loud speak 继电器 relay contact 配电板 switch board 配电箱 distribution box 变压器 transformer 保险丝 fuse 蜂鸣器 buzzer

69.敷板前驾驶室检查主干电缆安装

Inspection main cable installation for wheel house before paneling decoration.70.总配电板（应急配电板）绝缘电阻测量和保护装置可靠性试验

Measuring insulation resistance and reliability test protection device for main switchboard(emergency switchboard).71.主发电机（应急发电机）负荷及特性试验

Load and performance test for main generator(emergency generator).72.主发电机（应急发电机）电压、频率自动调节试验

Automatic governing test of voltage and frequency for main generator(emergency generator).73.主发电机并联运行试验

Parallel-running test for main generator.74.柴油发电机电压特性试验

Diesel generator voltage characteristic test.75.柴油发电机调速特性试验

Diesel generator governor sensitivity test.76.突加负荷试验

Test for taking on a full load suddenly.77.逆功率脱扣试验

Reverse power relay trip test.78.过电流脱扣试验 Over-current relay test.79.低压脱扣试验

Under voltage tripping test.80.联锁试验

Interlocking reliability test.81.二台主发电机负荷转移试验

Testing load charge-over between two main generator.82.轴带发电机负荷试验和航行时效用试验

Load test for shaft generator and its function test on sea trial.83.应急发电机自动供电试验

Automatic supply test of emergency generator.84.舵角指示器校准

Calibrating tudder angle indicator.85.舵角电动机遥控起动和报警试验

Remote starting and alarm test for steering gear motor.86.自动舵效用试验 Function test automatic pilot.87.锚机（舵机）电动机运转试验

Running test of motor for windless(steering gear).88.辅机和泵的电动机程序起动和自动转换

Sequence starting and automatic exchange of motors for auxiliary machine and pump.89.蓄电池和充电装置的充放电试验

Charge and discharge operation test for battery and charge equipment.90.机舱风、油（舱底泵）应急切断装置操作试验

Operation test of emergency switching-off device for oil pump and ventilator(bilge pump)in engine room.91.消防泵、应急消防泵遥控装置操作试验

Operation test of remote control device for fire pump and emergency fire pump.92.雾笛效用试验 Function test of fog horn.93.测深仪的换能器船台安装和水密性检查

Inspection installation and water tight transducer of echo sounder on berth.94.测深仪效用试验

Function test of echo sounder.95.计程仪水下部分船台安装和水密性检查

Inspection installation and water tight for log’s underwater parts on berth.96.航行试验中计程仪效用试验及误差调整

Function test and adjust error for log on sea trial.97.测向仪环状天线船台安装检查

Inspection installation for loop antenna of direction finder on berth.98.航行试验中测向仪效用试验及自差曲线校正

Function test and calibration self-heterodyne curve for direction finder on sea trial.99.组装报务台天线安装检查和绝缘测量

Inspection installation for antenna of radio console and measuring its insulation resistance.100.发讯机调谐表制表

Scheduling tuning chart of transmitter.101.航行试验中组装报务台效用试验 Function test of radio console on sea trial.102.航行试验中电罗经固定误差校正和效用试验

Calibration constant error and function for gyro compass on sea trial.103.航行试验（系泊试验）中雷达效用试验

Function test of radar on sea trial(mooring test).104.传感器报警设定值模拟试验 Simulating alarm test for fire detector.105.火警检测器自动报警试验

Automatic alarming test for fire detector.106.下列项目按系泊试验大纲进行系泊试验

The items are tested according to mooring test program as following as: 107.轮机员呼叫装置试验

Function test of engineer calling device.108.病室呼叫装置试验

Function test of calling device in hospital.109.超短波对讲机

Function test of ultra-short wave radio telephone.110.主机遥控系统性能试验

Function test of remote control system of main engine.111.无人机舱作4~6小时航行试验

UMS(unattended machinery space)sea trial continue 4~6 hours.112.电路绝缘电阻测量

Measuring installation resistance for circular.113.气象传真机效用试验

Function test for weather facsimile receive.6.内装

1.驾驶甲板空调、机械风管结构

A/C duct and vent duct structure of W/H Deck.2.A甲板空调、机械风管结构

A/C duct and vent duct structure of A-Deck.3.主甲板空调、机械风管结构

A/C duct and vent duct structure of Main Deck.4.救生（助）艇吊架结构和压重试验

Inspection the structure and loading test of the lifeboat(Rescue boat)davit.5.冷藏氟利昂管系密性试验

Ref.Freon piping to be done air-tightness test.6.冷藏氟利昂管系真空试验

Ref.Freon piping to be done vacuum test.7.冷藏机组保护装置试验及打冷试验

Ref.Plant to be done protection pice test and cooling-down test.8.机舱风管结构交验

E/R vent duct structure to be inspected.9.房舱空调氟利昂管系密性试验

Accommodation air-condition freon piping to be done air-tightness test.10.房舱空调氟利昂管系真空试验

Accommodation air-condition freon piping to be done vacuum test.11.房舱风量调整试验

Accommodation to be done air-flow adjustment test.12.房舱空调机组保护装置试验及冷/热效用试验

Accommodation A-C plant to be done protection device test.13.集控室单位式空调效用试验

E/C RM.Package A-C to be done function test.14.机舱空气干燥器效用试验及报警试验

E/R air drier to be done function test and alarm test.15.救生（助）艇收放试验

Lifeboat(rescue boat)to be done lowering and hoisting test.16.上层建筑水密门窗冲水试验

Superstructure water-tightness doors and windows to be done hosing test.17.房舱风机效用试验

Cabin supply fan to be done function test.18.上层建筑救生、消防设备交验

Superstructure life-saving and fire fighting equopment to be done inspection.19.厨房、洗衣间设备交验

Galley and laundry equopment to be done function.20.下甲板逃口――水密门冲水试验

Low deck escape-water-tightness doors to be hose test.21.上层建筑风雨密门窗安装后检查

Inspection water-tightness doors and windows of superstructure after fitting.22.上层建筑通风门门片安装后检查

Inspection air outlet grilles of superstructure after fitting.23.通道门操作和密性试验

Lobby doors to be done operation test and tightness test.24.冰箱效用试验

Refrigerator to be done function test.25.救助艇航行试验

Rescue boat to be done sea trial test.26.救助艇架结构完整性交验

Structure completeness of rescue boat davit to be inspected.27.救助艇架（救生筏吊架）静负荷试验

Rescue boat davit(life raft davit)to be done static loading test.28.救助艇架（救生筏吊架）动负荷试验

Rescue boat davit(life raft davit)to be done dynamic test.29.艏部舱室（舵机房）风管结构交验

Vent duct structure of bow cabin(steering gear RM.)to be inspection.30.菌形风头手动启闭试验

Mushroom outlet closing and opening by hand to be inspected.7、内装（铜工）

1.上层建筑压缩空气管系密性试验 Superstructure compressed air piping to be done air-tightness test.2.上层建筑控制空气管系密性试验

Superstructure compressed control air piping to be done air-tightness test.3.上层建筑供水管系密性试验

Superstructure water supply piping to be done air-tightness test.4.上层建筑消防管系（包括应急消防管系）密性试验

Superstructure fire fighting piping(including emergency fire fighting piping)to be done air-tightness test.5.上层建筑烟雾报警管系密性试验

Superstructure smoke detection piping to be done air-tightness test.6.厨房CO2管系密性试验

Galley CO2 piping to be done air-tightness test.7.上层建筑疏排水管系密性试验

Superstructure drainage air piping to be done air-tightness test.8.房舱凝水、落水管系畅通试验

Cabin condense piping to be done free-flowing test.9.房舱蒸汽管系密性试验

Cabin steam piping system to be done air-tightness test.10.甲板冲洗管系密性试验

Deck flushing piping system to be done air-tightness test.11.油漆间消防管系密性试验

Painting RM.Fire fighting pipe to be done air-tightness test.12.驾驶室喷淋管系效用试验

W/H jetting pipe to be done function test.8、内装（木工）

13.集控室浮动地板 Floating floor of E/C RM.14.集控室绝缘 Insulation of E/C RM.15.冷库地板绝缘

Insulation of Ref.RM.floor.16.冷库围壁绝缘

Insulation of Ref.RM.wall.17.冷库平顶绝缘

Insulation of Ref.RM.ceiling.18.冷库隔墙及顶大梁处绝缘

Insulation of separate wall and beam in Ref.RM.19.驾驶室浮动地板 Floating floor of W/H.20.主甲板浮动地板 Floating floor of main deck.21.驾驶室绝缘 Insulation of W/H.22.A甲板绝缘（包括A甲板A60绝缘）

Insulation of A-deck(including A60 insulation).23.主甲板绝缘

Insulation of main deck(including A60 insulation).24.应急发电机室绝缘（包括应急发电机室A60绝缘）

Insulation of emergency generator room(including A60 insulation).25.CO2室绝缘 Insulation of CO2 room.26.机舱逃口绝缘（包括机舱逃口A60绝缘）

Insulation of escape in E/R.(including A60 insulation).27.F11#舱壁绝缘（包括F11#舱壁A60绝缘）

Insulation of F11# bulkhead in E/R.(including A60 insulation).28.应急消防泵室绝缘（包括应急消防泵室A60绝缘）Insulation of emergency fire fighting pump RM.(including A60 insulation).29.舵机房绝缘

Insulation of steering gear RM.30.A甲板流平层敷料

Something deck covering of A-deck.31.主甲板流平层敷料

Something deck covering of main deck.32.驾驶甲板流平层敷料

Something deck covering of W/H deck.33.……舱室－围壁绝缘 One wall insulation of……

34.全船储藏室完整性提交

Completeness of all locker to be inspection.35.全船房舱完整性提交

Completeness of all cabin to be inspection.36.船长室、轮机长室（电机员室）敷板前检查隔热安装

Inspection insulation installation for master room, Chief engineer room(electrical engineer room)before panel.37.船长室（轮机长室）舱室完整性（木工和内部装饰）提交

Completeness delivery of accommodation(joiner work and interior decoration of accommodation)for master room(chief engineer room).

第三篇：船舶制造英语日常用语

船舶制造英语日常用语二

船检业务用英语

1、船体

1.56分段完工后结构完整性和焊缝检查

Inspection structure integrity and welding seam on completing No.56 block.2.上层建筑完后结构完整性检查

Inspection structure integrity after completing the superstructure.3.No.8 与No9分段合拢后大接头装配精确性和结构完整性检查

Checking the joint accuracy and structure integrity between No.8 and No.9 block after closed.4.上层建筑合拢后结构完整性检查

Checking structure integrity of superstructure(deckhouse)after closed.5.货舱口围板船上安装精度检查

Inspecting fitting accuracy of hatch coaming on berth.6.货舱口围板焊接后焊缝检查

Inspecting welding seam of hatch coaming after welding.7.No1压载水舱（No.15分段）气压试验（压头试验）检查

Inspection air pressure test(with water head)for No1.ballast water tank(No15 block).8.上甲板冲水试验检查

Inspection hosing test for upper deck.9.下水前测量船体主尺度、总长、两柱间长、型宽、型深、基线挠度

Measuring hull’s main dimensions:length overall(LOA.),length between perpendiculars(LPP.),breath molded(B.mld.),depth molded and deflection before launching.10.划线后检查吃水标尺至平板龙骨之间的距离

Inspection distance between draught marks and keel plate after marking out.11.吃水标志（载重线标志）安装后精确性检查

Inspecting fitting accuracy of draught mark(loadline mark).12.载重线标志划线后检查尺度

Inspection dimension of loadline after marking out.13.舵叶完工后检查

Checking rudder after completing(finished).14.货舱舱口盖焊缝和尺度检查

Inspection welding seam and dimension of cargo hatch cover.2、轮机内场

1.螺旋桨轴（中间轴）机加工尺寸检查

Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).2.检查螺旋桨轴与螺旋桨锥度接触面

Check for surface contact area(metallic contact)between stern shaft and propeller hub tapers.3.舵杆机加工尺寸检查

Inspection machining dimension of rudder stock.4.上舵承组装后检查

Inspection rudder carrier after assembly.5.舵销机加工尺寸检查

Inspection machining dimension of rudder pintle.6.舵杆、舵叶、舵销连接后中心线检查

Inspecting alignment of stock, rudder blade and pintle.7.锚投掷试验和拉力试验

Lowering test and tension test of anchor.8.轴系连接螺栓和孔尺寸测量

Measuring dimension of coupling bolts and reamer hole.3、轮机外场安装（钳工）1.防蚀板布置正确性检查

Inspection arrangement correctness of aluminium Anodes.2.船名牌（烟囱标志）安装正确性检查

Inspection installation correctness of ship’s name plate(funnel mark).3.水密小舱口盖（水密门、窗）启闭灵活性检查

Flexibility and hosing test for small water tight hatch cover(water tight door and window).4.货舱舱口盖密性试验（启闭试验、应急启闭试验）

Tightness test(opening and closing test,emergency opening and closing test)for cargo hatch cover.5.弃锚装置检查

Inspecting anchor throwing away appliance.6.轴、舵系镗孔前中心线定位检查

Inspecting centerline positioning for shaft system and rudder system before boring.7.轴系镗孔后光学校中检查

Optical aligned check for shaft system after boring.8.艉轴管滑油液压试验

Hydraulic test for L.O.pipe for stern tube.9.艉轴管前、后轴承与衬套直径测量

Measuring diameter of fore and aft stern tube bearing and bushes.10.艉轴管前、后衬套压入检查

Inspection push-up load for fore and aft stern tube bushes.11.螺旋桨轴与轴承间隙测量

Measuring clearance between propeller shaft & bearing.12.螺旋桨压入检查

Inspection wet fitting the propeller.13.艉轴密性装置的安装与密性试验

Fitting and tightness testing of propeller shaft before launching(after sea trial).14.艉轴管滑油系统的投油清洗 Flushing L.O.system of stern tube.15.舵叶0位检查

Inspecting zero(datum)position of rudder blade.16.舵装置完整性与轻便性检查

Inspecting integrity and flexibility of rudder appliance.17.舵止跳块的间隙测量

Measuring clearance of rudder jumping stopper.18.操舵装置完整性检查

Inspecting integrity of steering gear.19.舵轴承安装间隙测量

Measuring installation clearance of rudder bearing.20.舵机管路系统的投油清洗

Flushing of piping system for steering gear.21.舵机系泊试验

Mooring test of steering gear.22.舵机航行中操舵试验

Manoeuving test of steering gear during sea trial.23.舵机应急操舵试验

Emergency manoeuving test of steering gear.24.锚机管路系统的投油清洗 Flushing of piping system for windlass.25.锚机安装与校中检查

Installation and alignment inspection of windlass.26.锚机系泊试验 Mooring test of windlass.27.锚机航行中抛起锚试验

Anchoring and weighting test of windlass on sea trial.28.绞缆机完整性检查

Inspection integrity of mooring winch.29.绞缆机管路系统的投油清洗

Flushing of piping system for mooring winch.30.绞缆机系泊试验

Mooring test of mooring winch.31.舵机（锚机、绞缆机）液压系统安全装置调整

Adjusting safety device for hydraulic system of steering gear(windlass、mooring winch).32.4吨食物吊运转试验和吊重试验

Running test and hoisting test for 4t provision crane.33.救生艇收放试验 Lowering and hoisting test for life boat.34.救生艇航行试验

Sea trial for life boat.35.舷梯（引水员梯）压重试验

Loading test of accommodation ladder(pilot ladder).36.舷梯（引水员梯）和绞车收放试验

Lowering and hoisting test of accommodation ladder(pilot ladder).37.货舱舱口盖启闭试验

Opening and closing test for cargo hatch cover.38.货舱舱口盖应急启闭试验

Emergency opening and closing test for cargo hatch cover.39.水密小舱口盖（水密门、窗）启闭灵活性检查和冲水试验

Flexibility and hosing test for small water tight hatch cover(water tight door and window).40.主机垫片检查

Checking liner of main engine(M.E.).41.主机贯穿螺栓紧固度检查

Tightening inspection for through bolts of main engine(M.E.).42.下水后主机曲轴和中间轴连接后校中

Aligning main engine’s crank shaft and intermediate shaft after launching.43.下水后中间轴和螺旋桨连接后校中

Aligning intermediate shaft and propeller shaft after launching.44.主机动车前（航行试验后）曲轴甩档测量

Measuring deflection of crank shaft of M.E.before starting up(after sea trial).45.主机滑油（燃油）管路投油清洗 Flushing lubrication oil(fuel oil)system of M/E.46.轴带发电机及齿轮箱安装检查

Alignment inspection installation of shaft generator and gear box.47.主机报警和安全装置试验

Alarm testing and safety device testing of M/E.48.主机系泊（航行）试验并检查其附属泵与管路

Mooring test(sea trial)of M.E.and inspection attached pumps and piping system.49.轴带发电机运转试验及主机与轴带发电机之间的离合器的效用试验

Running test of shaft generator and clutching test between M.E.and shaft generator.50.航行试验中轴带发电机与柴油发电机之间的换车试验

Change over test between shaft generator and diesel generator on sea trial.51.主机航行试验后的拆检

Overhauling main engine after sea trial.52.主柴油发电机组安装检查

Installation inspection of main diesel generator.53.主柴油发电机动车前（系泊试验后）曲轴甩档测量

Measuring deflection of crank shaft of main diesel generator before running test(after sea trial).54.主柴油发电机的报警和安全装置试验

Alarm and safety device testing of main diesel generator.55.主柴油发电机运转试验

Running test of main diesel generator.56.应急柴油发电机运转试验

Running test of emergency main diesel generator.57.应急柴油发电机的安全装置试验

Safety device testing for emergency diesel generator.58.主（辅）空气压缩机的充气试验、安全阀和自动装置的调整

Charging test and safety valve and automatic device adjusting for main compressor(auxiliary compressor).59.应急空气压缩机的运转试验、安全阀和安全装置的调整

Running test and safety valve and safety device adjusting for emergency compressor.60.主空气瓶（控制空气瓶、汽笛空气瓶）装船后气密试验和安全阀的调整

Air tightness test and safety valve adjusting for main air receiver(control air receiver, air horn receiver)on board.61.辅锅炉（废气锅炉）装船后气密试验

Air tightness test for auxiliary boiler(economize boiler)on board.62.辅锅炉安全阀检验及蓄压试验

Safety valve adjusting and accumulating test for auxiliary boiler.63.辅锅炉自动控制装置试验

Automatic controller test for auxiliary boiler.64.废气锅炉效用试验

Function test for economizer.65.压载泵效用试验和自动控制装置试验

Function test and automatic controller test for ballast pump.66.舱底水油水分离器（污水处理装置、制淡装置、焚烧炉）效用试验

Function test of bilge oily water separator(sewage treatment plant, fresh water generator, incinerator).67.机舱行车吊重试验

Hoisting test of engine room crane.68.机修间设备运转试验

Running test of machines in repair room.无线电话 radio telephone 电视机和收音机 TV and radio set 电视机和收音机天线共用器

antenna multi coupler of TV and radio set 电罗经 gyro compass 磁罗经 magnetic compass 电脉冲 electrical impulse 应急电站 emergency power station 扬声器 loud speak 继电器 relay contact 配电板 switch board 配电箱 distribution box 变压器 transformer 保险丝 fuse 蜂鸣器 buzzer

69.敷板前驾驶室检查主干电缆安装

Inspection main cable installation for wheel house before paneling decoration.70.总配电板（应急配电板）绝缘电阻测量和保护装置可靠性试验

Measuring insulation resistance and reliability test protection device for main switchboard(emergency switchboard).

第四篇：船体英语

一． 名词部分

（一）船舶

1．船舶与海上设施的类型 Type of Ship and Offshore Unit 货船 Cargo Ship 杂货船 General cargo ship 干货船 Dry cargo ship 散货船 Bulk carrier 矿沙船 Ore carrier 运煤船 Coal carrier 集装箱船 Container ship 滚装货船 Ro/Ro ship 冷藏船 Refrigerated ship 运畜船 Cattle carrier 运木船 Timber carrier 近海供应船 Offshore supply ship 散装矿砂船 Bulk Ore carrier 混装船 Combination carrier 载驳母船 Barge Carrier 汽车运输船 Car carrier 液货船 Liquid Cargo Carrier 油船 Oil tanker 化学品液货船 Chemical tanker 液化气体船 Liquefied gas carrier 油矿两用船 Oil/ore carrier 油散两用船 Oil/bulk carrier 油散矿三用船 Oil/bulk/ore carrier 客船 Passenger Ship 客船 Passenger ship 豪华旅游客船 Cruise ship 旅游船 Tourist ship 高速客船 High speed passenger craft 双体客船 Passenger catamaran 客货船 Passenger-cargo ship 客箱船 Passenger container ship 客滚船 Ro/Ro Passenger Ship 高速船 High Speed Craft 全垫升气垫船 Air-cushion Vehicle 水面效应船 Surface Effect Ship 双体气垫船 Air-cushion Catamaran 侧壁气垫船 Side-wall Hovercraft 高速双体船 High Speed Catamaran 2 高速单体船 High Speed Monohull Craft 地效翼船 Wing-in Ground Craft 水翼船 Hydrofoil Craft 动力支承船 Dynamically Supported Craft 两栖船 Amphibious Craft 小水面单体船 Small Waterplane Area Single Hull Ship 小水面双体船 Small Waterplane Area Twin Hull Ship 驳船 Barge 客驳 Passenger Barge 货驳 Cargo Barge 敞口驳 Open Barge 甲板驳 Deck Barge 集装箱驳 Container Barge 分节驳 Integrated Barge 开底驳 Hopper Barge 油驳 Oil Barge 趸船（箱形驳）Pontoon 拖船 Tug 港作拖船 Harbour Tug 打捞拖船 Salvage Tug 顶推船 Pusher 近海供应拖船 Offshore tug/supply ship 工程船 Engineering Ship 挖泥船 Dredger 耙吸式挖泥船 Trailing suction dredger 绞吸式挖泥船 Cutter suction dredger 链斗式挖泥船 Bucket dredger 抓斗式挖泥船 Grab dredger 铲斗式挖泥船 Dipper dredger 吹泥船 Reclamation craft 开底泥驳 Hopper Barge 对开泥驳 Split Hopper Barge 起重船 Floating Crane 浮船坞 Floating Dock 打桩船 Floating Pile Driver 布缆船 Cable Layer 潜水工作船 Diving Boat 港区工作船 Harbour Operating Ship 破冰船 Ice breaker 消防船 Fire Boat 救护船/救助船 Rescue Ship 引水船 Pilot Vessel 海关船 Customs Boat 巡逻船 Patrol Boat 3 布标船 Buoy Layer 灯标船 Beacon Boat 交通艇 Traffic Boat 垃圾船 Garbage Boat 浮油回收船 Oil Recovery Ship 污水处理船 Sewage Disposal Vessel 海水淡化船 Distilling Ship 渡船 Ferry 乘客渡船 Passenger Ferry 火车渡船 Train Ferry 车客渡船 Vehicle Passenger Ferry 海峡渡船 Channel Ferry 渔船 Fishing Vessel 渔品加工船 Fish-Factory Ship 拖网渔船 Trawler 围网渔船 Netter 捕鲸船 Whaling Ship 活鱼运输船 Live Fish Carrier 其他船舶

科学调查船 Research ship 训练船 Training Ship 特殊用途船 Special purpose ship 内河船 Inland Waterways Ship 海上设施

海上移动平台 Mobile Offshore Unit 海上移动钻井平台 Mobile Offshore Drilling Unit 水面式平台 Surface Unit 船式平台 Ship-type Unit 驳船平台 Barge-type Unit 自升式平台 Self-elevating Unit 柱稳式平台 Column-stabilized Unit 半潜式平台 Semi-submersible Unit 坐底式平台 Submersible Unit 采油平台 Production Unit 储油平台 Storage Unit 生活平台 Accommodation Unit 修理平台 Repair Unit 海上固定平台 Fixed Offshore Platform 海底管道 Submarine Pipeline 潜水系统和潜水器 Diving System and Submersible 单点系泊 Single Point Mooring(SPM)浮式生产与储油装置 Floating Production and Storage Unit(FSUs)浮式生产、储存及卸载系统 Floating Production, Storage and Offloading System(FPSOs)4 2． 数据与资料 Data and Information 数据

总长 Length overall(LOA)垂线间长 Length bet.perpendiculars(LBP)首、尾垂线 Forward and after perpendiculars 型宽 Moulded breadth 型深 Moulded depth 建造日期 Date of build 签订建造合同日期 Date of building contract 龙骨安放日期 Date of keel laid 交船日期 Date of delivery 下水日期 Launching date 重大改建 Major conversion 安放龙骨或船舶处于相似建造阶段的日期

Date on which keel was laid or ship was at a similar stage of construction 签订改建合同日期 Date of conversion contract 改建完工日期 Date of completion of conversion 船舶所有人 Owner 经营人 Operator 承租人 Charterer 船舶编号或呼号 Distinctive number or letters 航行区域 Navigation area/Service area/Trade area 曾用过的船名 Former Name 姐妹船 Sister Ship 总吨位 Gross tonnage 净吨位 Net tonnage 排水量 Displacement 载货量 Cargo weight 载重量 Deadweight 空船重量 Light(-ship)weight 吃水(首、尾、平均)Draft(fwd, aft, mean)稳性 Stability 完整稳性 Intact stability 破舱稳性 Damaged stability 分舱（抗沉性）Subpision 初稳性高度 Metacentric height 衡准数 Criterion numeral 剖面模数 Section modulus 惯性矩 Moment of inertia 纵总强度 Longitudinal strength 局部强度 Local strength 方形系数 Block coefficient 静水弯矩 Still water bending moment 5 重心垂直高度 Vertical height of centre of gravity 屈服应力 Yield stress 标准舷弧 Standard sheer 防火分隔 Fire pision 航区限制 Navigation area restriction 海况限制 Sea state restriction 天气限制 Weather restriction 最大抗风暴能力 Max.weatherliness 储备浮力 Reserve buoyancy 续航力 Endurance 渗透率 Permeability 盲区 Blind area 共振区域 Resonance region 容许载荷 Permissible load 核定载客数 Number of persons certified to carry 干舷： Freeboard 热带干舷 Tropical freeboard 夏季干舷 Summer freeboard 冬季干舷 Winter freeboard 北大西洋冬季干舷 Winter North Atlantic freeboard 热带木材干舷 Timber tropical 夏季木材干舷 Timber summer 冬季木材干舷 Timber winter 北大西洋冬季木材干舷 Timber winter North Atlantic freeboard 淡水宽限 Allowance for fresh water 减少干舷的B 型船舶 Type B with reduced freeboard 增加干舷的B 型船舶 Type B with increased freeboard 载重线： Load line 载重线标志 Loadline marks 资料

防火控制图 Fire control plans 海图(up-to-date 最新)Charts 航路指南 Sailing direction 灯塔表 Lists of lights 航行通告 Notices to mariners 潮汐表 Tide tables 航海出版物 Nautical publications 应变部署表 Muster list 国际信号规则 International Code of Signals 航海日志 Deck log book 机舱日志 Engine room log book 无线电日志 Radio log book 6 线型图 Lines 稳性资料 Stability information 装载手册 Loading manual 干舷计算书 Freeboard calculations 配载图 Stowage plan 操作说明书 Operation instructions 维修计划 Maintenance plan 训练手册 Training manual 船上维修保养指南 Instructions for on-board maintenance 弃船训练演习手册 Abandon ship training and drill manual 3． 舱室处所 Compartments or Spaces 舱室

工作和设备舱室： 驾驶室wheel house 海图室 chart room 报务室 radio room 雷达室 radar room 声纳室 sonar room 主机舱 main engine room 主机操纵室 main engine control room 辅机舱 auxiliary engine room 锅炉舱 boiler room 机炉舱 engine and boiler room 减速器舱 reduction gear room 舵机舱 steering gear room 通风机室 fan room 变流机室 commutator room 空调室 air-conditioner room 应急发电机室 emergency generator room 冷冻机室 refrigerator room 灭火装置室 fire control room 蓄电池室 battery room

陀螺罗经室 gyro-compass room 方位水平仪室 azimuth level room 计程仪舱 log room 导弹舱 missile room 弹药舱 magazine 深弹舱 depth charge room 弹药转运舱 ammunition lobby 声纳舱 sonacelle, sonar nacelle 7 机修间 workshop 电工间 electrician‟s store 木工间 carpenter‟s store 锚链舱 chain locker 桅屋 mast house 洗消室 decontamination room

居住舱室 Accommodation, living accommodation 客舱 Cabin 船员舱室 crew‟s cabin 墙壁 wall 天花板 top ceiling 侧壁板 side ceiling 里子板 lining 装饰 decoration 家具 furniture 书桌 desk 衣橱 wardrobe 梳妆台 dressing table 书柜table bureaux 餐具柜 dresser 椅子 chair 沙发 sofa 桌子 table 帷幔 drapery 窗帘 curtain 地毯 carpet

货舱 cargo hold 货油舱 cargo oil tank 集装箱舱 container hold

冷藏货舱 refrigerated cargo hold

液化天燃气舱 liquefied natural gas tank 邮件舱 mail room 行李舱 luggage room 汽车舱 vehicle hold 液舱 liquid tank 燃油舱 fuel oil tank 滑油舱 lubricating oil tank 压载水舱 ballast tank 淡水舱 fresh water tank 污水舱 bilge tank 储藏室 store, store room 帆缆间 hawser store 油漆间 paint room 粮食库 provision store

冷藏库 refrigerating chamber 其他：

首尖舱 fore peak tank 尾尖舱 aft peak tank 顶边舱：topside tank

甲板强横梁 deck transverse 与舱口一直线的垂直边板 vertical side plating in line with hatch 船壳板 shell plating 斜底板 sloping plating 底边舱 hopper side tank 双层底舱 double bottom tank 翼舱 wing tank 边舱 side tank平衡舱 heeling tank 深舱 deep tank 残油舱 sludge/oil residue tank 隔离空舱 cofferdam 空舱 void tank 处所

货物处所： Cargo spaces 货舱 Cargo hold 货油舱 Cargo oil tank 液货舱 Liquid cargo tank 围壁通道 Trunk 起居处所： Accommodation spaces 公共处所 Public space 走廊 Corridor 盥洗室 Lavatory 住所 Cabin 办公室 Office 医务室 Hospital 放映室 Cinema 游戏室 Game room 娱乐室 Hobby room 理发室 Barber shop 配膳室(无烹调设备)Pantry(containing no cooking appliances)公共处所： Public spaces: 大厅 Hall 餐室 Dining room 9 休息室 Lounge 类似的固定围闭处所 Similar permanently enclosed spaces 服务处所： Service spaces： 厨房 Galley 配膳室(设有烹调设备的)Pantry(containing cooking appliances)储物间 Locker 邮件舱 Mail room 贵重物品室 Specie room 储藏室 Store room 工作间 Workshop 围壁通道 Trunk 特种处所： Special category spaces： 舱壁甲板以上或以下围闭的车辆处所

Enclosed vehicle spaces above and below the bulkhead deck 机器处所： Machinery spaces：

A 类机器处所 Machinery space of category A 装有下列机械的处所 Spaces containing: 推进机械；Propulsion machinery, 锅炉； Boilers，燃油装置；Oil fuel units，蒸汽机和内燃机；Steam and internal combustion engines, 发电机和主要电动机；Generators and major electrical machinery, 加油站；Oil filling station, 冷藏机；Refrigerating installation, 防摇装置；Stabilizing installation, 通风机；Ventilation installation，空气调节机械。Air conditioning machinery.围壁通道 Trunk 控制站： Control stations： 下列设备所在/集中的处所： 船舶无线电设备； 主要航行设备； 应急电源。/ 火警指示器或失火控制设备。

Spaces in which the following located/centralized: Ship‟s radio equipment, Main navigating equipment, Emergency source of power./ Fire recording and fire control equipment.4．高级船员和船员

船长 Master(商船船长的正式称谓)Captain(商船船长的尊称)小船驾长 Skipper 大付 Chief officer 二付 Second officer 10 三付 Third officer 驾助 Assistant officer 轮机长 Chief engineer 政委 s Commissar 大管轮 First engineer 二管轮 Second engineer 三管轮 Third engineer 轮机员 Engineer 轮助 Assistant engineer 电机长 Chief electrician 电机员 Electrician 电助 Assitant electrician 水手长 Boatswain 付水手长 Cassab 一等水手 Able seaman 水手(original)seaman 实习生 Apprentice 见习生 Cadet 机工长 Chief motorman 机工 Motorman 加油 Greaser 铜匠 Fitter 大厨 Chief cook 厨师 Cook 事务长 Chief steward 服务员 Steward 报务主任 Chief radio operator/officer 报务员 Radio operator/officer 甲板部 Deck department 轮机部 Machinery department 5． 船级

入级条件 condition of classification 保持船级条